2010 Toyota Tundra Oil Change Procedure

If the fluid temperature is 133F 56C or more turn OFF the engine and wait until the fluid temperature drops to 115F 46C or less and then perform steps 3 and 4 again from the beginning. After it has been cleaned reinsert it into the tube and pull it back out.

2010 Toyota Tundra Oil Change Procedure - If you're searching for picture and video information linked to the key word you've come to visit the ideal blog. Our site gives you hints for viewing the highest quality video and picture content, search and find more informative video content and graphics that fit your interests. includes one of thousands of video collections from several sources, particularly Youtube, so we recommend this video that you see. It is also possible to bring about supporting this site by sharing videos and images that you enjoy on this blog on your social media accounts like Facebook and Instagram or educate your closest friends share your experiences concerning the simplicity of access to downloads and the information you get on this site. This site is for them to stop by this site.

For Lexus Toyota Oil Filter Housing Cover W Plug O Ring Oil Filter Kit Oes Automotive Engines Components

If the pan was easy to replace I might just swap it out but I believe you will need to remove a cross member to get it out of there.

2010 toyota tundra oil change procedure. Now all of my upcoming oil changes will be easier and I know it was done right the first time. Complete video instructions to add transmission fluid to a 2010 Toyota Tundra 57L V8 Extended Crew Cab Pickup 4 Door. For models equipped with the 46l v8 or the 57l v8 toyota recommends using sae 0w-20 or 5w-20.

Great for the differential. Check that electrical systems such as the air conditioning system audio system and lighting system are off. Toyota recommends using sae 5w-30 engine oil for the 2010 tundra equipped with the v6 engine.

In the future you also can ask your Toyota dealer to reset the light after changing the oil. On person loosens the brake bleeder at a wheel. With the Trip Reset button pushed down turn the ignition key to the ACC On position.

With your left hand push the Trip Reset button. Loosen the overflow plug 5mm hex located on the bottom of the AT fluid pan to ensure its ability to be removed when required. Move the shift lever to D and quickly move back and forth between N and D once within 15 seconds for at least 6 seconds.

While holding reset button switch ignition to ON position. Now that you have cycled through the gears you can begin the ATF check on your Toyota Tundra. Called one dealership and they wanted 18995 for a transmission fluid flush.

Although 5w-20 can be used toyota recommends using 0w-20 for the best fuel economy. If you have no idea when the last time your Tundras oil was changed or if you happen to have done a lot of towing or if your oil change is overdue changing the oil itself may vary well solve the problem. There is a tube in your Tundra that takes the oil from the pan to the oil pump.

Proceed to step 6 Check the ATF fluid level. Jump terminals 4 and 13 at the DLC with an appropriate jumper Start the engine to idle. Oil Change Light Reset Toyota Tundra 2010 2011 2012 2013 2014 2015 Procedure Turn the ignition to the RUN position.

With a level truck it was another 24 oz to the fill bottom-Check the label on the differential. I would find a larger oil plug and tap it to the larger size. Pulling out the dipstick use a clean rag to wipe the dipstick.

When and how to check fluid level engine should be running. Step 1 Turn your key to the On notch and press your trip odometer knob until Trip A is displayed. I tow a lot during the summer and have concerns about not taking care.

Press and hold trip meter reset knob and turn the ignition to the RUN position. 10w-30 oil can be used in case 5w-30 is not available but should be changed when 5w-30 becomes available. If you should remove the overflow plug now have a pan ready as fluid will spill.

Toyota Tundra Oil Maint Required Message Reset Procedure for Model Years 2005-2015. Wish I had enough left for the gearbox on my Jet 10 bandsaw. Follow these steps to add transmission fluid in a 2010 Toyota Tundra 57L V8 Extended Crew Cab Pickup 4 Door.

Called another dealership and they said a flush isnt necessary since we have the sealed transmission but would drop the pan and change out the 4 qts for 4995. The procedure is applicable to the second-generation Toyota Tundra pickup truck 2007 to 2010. If you like to reset any maintenance oil light after an oil change.

Then the other lets off the brake pedal and the process is. Once the bleeder is open the other person presses the brake pedal to the floor once time and holds it. That it is the full procedure how to reset low engine oil pressure warning light Toyota Tundra 2 generation.

Continue holding the Trip Reset button down until the odometer reading displays 000000 for one second. The other person closes the bleeder. The oil change reminder indicator should be reset.

No additive specified for oil replacement-Amsoil was about 15 a qt as well. My truck took about 8 quarts 25 on a Fumoto and 6 on a filter. This is called the pickup tube.

Someone probably cross threaded it or hit it with a air wrench would be my guess. The tundra threads are quite small from my older toyota drain plug. Discussion Starter 1 Feb 1 2010.

Mine said go to the owners manual. Or reset check engine light airbag light inspection key or insp errors when maint reqd for Toyota cars. I think I spent about 50 on oil Mobil 1 synthetic Walmart has 5 quart jugs cheap.

-Buy extra oil. In the fluid temperature detection mode the D shift indicator comes ON goes OFF. Make sure trip meter A is displayed and turn the ignition off.

With vehicle ignition switched to ON position make sure odometer is showing Tripmeter A then turn the ignition switch to OFF position. Plus its kinda fun to work on your truck. Look to see if the fluid is in the HOT segment while you have it running at normal temperatures.

Most tundra owners claim 4 qts enough. Place your drain pan underneath the transmission fluid. Push and hold the TRIP reset or MODE button.